Local Services

Remodeler Santa Ana CA

Rv Upholstery Santa Ana

Published Apr 05, 25

11 min read

Table of Contents

– Rv Upholstery Santa Ana, CA
– OCRV Center
– Rv Restoration Companies Santa Ana, CA
– Rv Carpet Replacement Santa Ana, CA
– Rv Restoration Companies Santa Ana, CA
– Rv Refrigerator Replacement Santa Ana, CA
– Rv Restoration Companies Santa Ana, CA
– Rv Replacement Awnings Santa Ana, CA
– Replacement Windows For Campers Santa Ana, CA
– Rv Couch Santa Ana, CA
– Rv Dining Table Santa Ana, CA
– Rv Replacement Furniture Santa Ana, CA
– Awning Installation Santa Ana, CA
– OCRV Center

Rv Upholstery Santa Ana, CA

OCRV Center

23281 La Palma Ave Yorba Linda, CA 92887
(714) 909-1444
OCRV Center

I'm gon na get all this linoleum out. I'm gon na get the plastic back past the side of the door, and after that truly have a good look at how things look.

So up here in this edge it's punky. It's soft sufficient that I assume with a hammer and a flat bar, I can start tearing some plywood out of there. And what that bit exploratory surgery is gon na do is offer me a feel for what the system looks like, which will certainly then tell me, you know, I think at some time here, gon na finish up running a circular saw, and reducing back to excellent timber and afterwards replacing the poor things.

Rv Restoration Companies Santa Ana, CA

So like I claimed, I believe I can, I can peel sufficient of the negative things out of there to at the very least obtain a feel for what I have. Well, truthfully, where I go to that quickly suffices to offer me a good feeling for determining what I need to do following.

We can replace that as we obtain the new flooring in below also. What this will certainly allow me do, seeing this, I believe what I can do next is obtain a circ saw reduced back below someplace, and then peel back to that factor. We'll go from there and just keep, like I said previously, taking a negative flooring out up until we obtain to strong stuff.

Rv Carpet Replacement Santa Ana, CA

Currently it's feasible that this is gon na become type of L-shape, due to the fact that in the facility of the camper over here, that floor appears pretty good, however naturally that bad area is still there by the door, and this needs to appear. So currently my agenda is reducing to a joist right here someplace to reach strong wood.

Currently, the other point I wan na mention is this. When I took that initial chunk of plywood out, I did that cutting and I removed the material, and I realized quite quick, I need to've had a mask on. There's a great deal going on there. If nothing else, I'm developing a great deal of dust in a constrained area, so mask.

Rv Restoration Companies Santa Ana, CA

One of the points I do wish to point out, I'm being truly mindful working around the membrane that's under the floor. And the reason is the membrane layer is really still intact, and I do not intend to all of a sudden get my foot in the wrong spot and action via it or something and placed a big tear in it.

So I'm truly very carefully working around this by strolling only on the joists, the sleepers, and after that likewise simply being truly, actually mindful concerning where I step and where I place electronic cameras and stuff. Right here's where I'm at. On this beyond the camper, among the things that's really great news is that home plates on the bottom of the walls are done in really good condition, which honestly surprised me for the condition of everything else in right here.

On this certain wall, the joist, the last edge piece that's out right here outside of the camper is still there and it remains in fine form. But the trouble I'm up versus is that if I do not sister something together with it here, when I are available in with plywood, I won't have anything to nail the plywood to.

Rv Refrigerator Replacement Santa Ana, CA

I mean, all I'm doing is getting it in area, and then I'm going with screws for whatever rather than nails just to make certain I get a good bite, and it remains stuck once it's in there. I'm simply going to drive screw after screw after screw to protect these components with each other and make sure they remain stuck.

So I'm obtaining that edge piece in. And among things to be observant of is that as a result of the skin on the outside of the trailer, I can not get bolts through this, the board we simply put in and tie it into that. Instead I am making use of angle irons here.

Talk much more concerning that. But one of the important things, among the important things too, that I wanted to mention is that I did a button, a screw button, after I started on that very first item, I was including back in. I realized that those screws I was utilizing were nowhere near beefy adequate wherefore we were asking of them.

Rv Restoration Companies Santa Ana, CA

Currently with these, what that angle iron will certainly do is connect these two pieces with each other. And afterwards the various other thing to remember below is that once the deck begins, once plywood begins, which overlays these pieces and all, and obtains secured to them, that additionally is mosting likely to aid link every little thing so that it connects these parts together.

The angle iron plus the plywood is gon na assist with that. And there's absolutely nothing, absolutely nothing funky regarding these. Hardware shop stuff and that effect driver, vroom, vroom. That's why I keep my hearing defense in, even when all I'm doing is driving screws. It's loud anyhow. And in a restricted atmosphere such as this, you understand, once more, we intend to be security aware throughout this.

And the reason for that is I made use of a jigsaw, handheld jigsaw, and I cut them back and they're not necessarily reduce back yet to the factor where I'm at excellent wood, and I'm gon na tie into them. We'll enter into that yet. But what I intended to do was reduced back where I understood completions were bad, and I required to provide some clearance to make it very easy to obtain that edge item in.

Rv Replacement Awnings Santa Ana, CA

The following action is going to be start bringing those sleepers, the floor joists back in, and then from there insulation and plywood. More flooring, flooring, floors are us.

And I possess a staple gun and I could staple it, but I felt like I want something on that that I recognize is gon na be a little bit more durable link is, is most definitely gon na maintain that textile limited. Right here's my plan with that. I have actually obtained a table saw in the building, and we'll talk more about devices below in simply a second.

And I think it's truly vital that this is treated because it's going to live outdoors under the camper, not inside the camper. And of program the sleepers, the joists are on side (Rv Upholstery Santa Ana).

Utilizing a counter sink in my drill, I have actually currently pre-drilled these, and I did that so that when I start driving screws, I don't take a chance of splitting these. So I'm rather near the next action, which is crawl underneath there, and drive screws with the pre-drilled holes.

Replacement Windows For Campers Santa Ana, CA

We're obtaining all set up here. The screws ought to likewise be exterior to make sure that they're gon na not rust away on you. When you have actually obtained these all set currently, like I claimed, we can get underneath there, and be some tricky cam work to get this for you, however we'll get these secured up in place to the base of the sleepers.

And after that obviously, an option of hand tools, circ saw, belt sander, jigsaw, saws all. And with the larger devices, with the miter saw and the table saw, that was necessary, due to the fact that as I started to produce those new joists that I was exchanging in, I didn't intend to have to constantly go to a few other shop and cut components, return, cut components, come back.

Following, um, allow's crawl under a camper. Well, I'm under the camper currently, certainly, and you can see there, I have actually currently obtained a number of battens in place and another one right here. What I'm doing is feeling via the fabric, and after that there's a joist right there.

And then, brr, brr, need to be able to simply drive some screws. The batten is just acting like a really big washing machine to make certain that that material does not have the possibility to tear with and come loose.

Rv Couch Santa Ana, CA

The following thing inside below is to look for a factor where we obtain to good product, and after that tie right into that with a new item in a method that structurally is gon na work. And likewise just is basic sufficient to do. Allow me get some tools drawn with each other, and after that we'll look at out with the old and in with the brand-new below.

Replacement Windows For Campers Santa Ana, CA

I have actually obtained a poor end, conveniently identified, since that wood was in actually, actually poor form. I'm looking for a part here where it gets audio.

Rv Dining Table Santa Ana, CA

If I had to return additionally with the system I will use right here, I would certainly be okay keeping that. Rv Upholstery Santa Ana. If in order to remove bad material, I had to reduce back right here where I'm not over a steel frame part, I would do that. What I have actually done so much lies the steel

And the following thing, let's obtain that bad area reduced out. And what I desire to do as I cut is also lift a little bit. And I've currently obtained a brand-new item cut.

There we go. And right here's the important things. The secret to this are items of scrap plywood. And the means this is gon na job is we're gon na bridge that seam with those plywood scraps. Plywood is unbelievably solid stuff. And combined with the plywood, we're mosting likely to add adhesive and screws, and that is really gon na make this generally similar to having one long piece once more when we're done.

I have obtained in my warm little hands, another item to go on that side. I simply have to get my system out of the method below.

Rv Replacement Furniture Santa Ana, CA

And when this is done, that is gon na be an actually, truly solid system. Right here's a large minute. The last piece of plywood will obtain placed in, however allowed's speak about a couple points. Notice the insulation in the floor. I have actually insulated the floor with what's called mineral woollen or rock wool insulation.

Because of using that, that's component of the factor that I desired to make sure those battens got under the textile. And the factor being that that mineral woollen, it's obtained some thickness to it.

When I'm cutting this piece, the item that's gon na load in here, I would certainly like to keep the factory edge on that end butting versus the factory edge that's already in location, and then the cut edge goes out here up versus the wall. Currently, if you have to do a trim, you have to do a trim, and in this situation I did.

If you got ta do it, you got ta do it, but it in the perfect world, factory edge to factory side right here on the lengthy seams, and on the brief seams where items are satisfying. The other thing is that we wish to be fifty percent on a joist. What I suggest by that is that this portion of plywood is half on this joist, and after that the following piece of plywood is gon na come on below, so it's got something to be fastened to, and that's just a, you recognize, a building and construction standard that you constantly comply with when you're doing flooring or roofing.

Awning Installation Santa Ana, CA

There aren't any type of portions of insulation laying on top of the framing. I have actually got, if you look out below, I have actually got these places noted on the wall, to ensure that as I come with a screw gun, more on that particular in a 2nd, I recognize that sleeper, that joist exists, center exists, facility exists.

I must have an inch and a quarter staple going into it. I do not have a stapler that'll do that, but I do own a screw weapon that I can use to drive long screws. So I'm doing this with a screw gun rather of a stapler. All right, a lot of chatting, and let's check out getting the plywood to come in.

OCRV Center

Address: 23281 La Palma Ave Yorba Linda, CA 92887
Phone: (714) 909-1444
OCRV Center

Well, we ended with a great deal of screwing around.The entire flooring was a great deal of screwing about. Simply a great deal of little fussy points to do to get this right, but most definitely worth doing, because clearly there were some poor areas in here that needed to go. With those screws, if there's any location where you seem like you might've missed out on, get a standard cordless screwdriver, back those screws out.

Share us on...

Table of Contents

– Rv Upholstery Santa Ana, CA
– OCRV Center
– Rv Restoration Companies Santa Ana, CA
– Rv Carpet Replacement Santa Ana, CA
– Rv Restoration Companies Santa Ana, CA
– Rv Refrigerator Replacement Santa Ana, CA
– Rv Restoration Companies Santa Ana, CA
– Rv Replacement Awnings Santa Ana, CA
– Replacement Windows For Campers Santa Ana, CA
– Rv Couch Santa Ana, CA
– Rv Dining Table Santa Ana, CA
– Rv Replacement Furniture Santa Ana, CA
– Awning Installation Santa Ana, CA
– OCRV Center

Local Services

Navigation

Home